TS1 Firmware 4.1_N

TS1 Quick guide 4.1

TS1 Firmware 4.18
(pre-release)

What’s new in the 4.18 release (pre-release)

The 4.18 has the following improvements:

For Triggers and drums modes

• Euclidian functionality for Trigger and Drums modes.

  • Added advanced edit mode (‘E’ icon on upper rigth shall be On to enter this mode)

    • Menu/Shift (Up/Down) to select track.

    • Select (turn) to change Euclidian events number, (see graphical representation on line 1.)

    • Select (push) to apply it on desired track.

    • Push Edit to exit advanded edit.

• Polymeters functionality for Triggers and Drums.

  • See TRIGGER/DRUMS LENGTH page in setting mode to set the individual track length.

For Sequences modes

• 4 user scales, with length and progression choice between each note in the scale.

For Trigger drums and Sequences modes

• Probabilities from 0 to 100% to trigg the ‘X’ Icon.

  • See chance page in setting mode.

  • 3 individuals probabilities are available for :

    Trig, Drums and Notes.

Note : See the page Tips&Tricks for the new shorcuts explanation.

Important :

1) This is a pre-release, some functionalities are not fully tested like Song mode.

2) Due to new features added that need code space, the following functionalities are not present in this release

• LoFi DCO on CV1 output.

• Reverse functionality for notes sequences.

3) For TS1 version 3.7 and older, (same recommendations) due to the add of new icons, for old version owner it is imperative to erase the permanent memory of the TS1 using the service mode:

• Download the firmware, then install it on the TS1 using the procedure described in the reference manual.

• Once the firmware is installed, enter service mode: SHIFT and EDIT pressed when powering up.

• Perform all of the following operations: - ERASE ALL TRIGGERS, SEQUENCES, CHORDS, SONG, SCENES.

• Enter settings mode: Turn the Mode knob to the setting position then turn select to "SETTINGS" and press Select.

• Press Edit or Select to enter in setting edition, browse the general menu until "Init Settings" press Select (blink arrow) change the state to "On" then press Select to Init the settings.

Restart the TS1 normally, if you get an inconsistent display repeat the erase the memory or reset settings operation.

TS1 Firmware 3.9a

What’s new in the 3.9a revision

The 3.9firmware brings new improvements versus 3.8 version, these are the following:

• Full and rapid access to Mutes, Solo and Transpose for trigger, drums , sequences 1,2,3,4/Chord in any pattern modes.

• Full support for new remote app version 1.6 with added buttons for Solo tracks, Un-mute and Un-solo sequences.

• One LoFi DCO on CV/Gate1 generating Sawtooth waveform.Dedicated for bass and playing only Sequence 1 notes, from 1 to 3 octave (0 to 4 if transpose -12 is enabled).

Important:

Due to the add of new icons, for old version owner it is imperative to erase the permanent memory of the TS1 using the service mode:

1) Download the firmware, then install it on the TS1 using the procedure described in the reference manual.
2) Once the firmware is installed, enter service mode: SHIFT and EDIT pressed when powering up.
3) Perform all of the following operations: - ERASE ALL TRIGGERS, SEQUENCES, CHORDS, SONG, SCENES.
4) Enter settings mode: Turn the Mode knob to the setting position then turn select to "SETTINGS" and press Select. Press Edit or Select to enter in setting edition, browse the general menu until "Init Settings" press Select (blink arrow) change the state to "On" then press Select to Init the settings.

Restart the TS1 normally, if you get an inconsistent display repeat the erase the memory or reset settings operation.

TS1 Quick Guide 3.9

TS1 reference guide

New TS1 guide 3.9